Infiniti vehicles are equipped with the convenient HomeLink system, allowing you to integrate and control various home automation devices directly from your car. One of the most popular uses is programming your garage door opener. This guide will provide you with step-by-step instructions on how to program your Infiniti HomeLink garage door opener, ensuring a seamless entry every time you arrive home.
Whether your HomeLink buttons are located on your rearview mirror, visor, or front console, the programming process remains consistent. Follow these instructions to easily set up your system.
Clearing Previous HomeLink Programming (If Necessary)
If you are programming HomeLink for the first time or want to clear previous settings, begin by clearing the system’s memory. Note: This step is only needed if you want to reset the HomeLink system. If you are programming a new button, you can skip this step.
To clear the memory, press and hold the two outer HomeLink buttons simultaneously. Keep holding them until the red indicator light starts to flash rapidly. This usually takes about 20 seconds. The flashing light indicates that the system memory has been successfully cleared.
Programming Your Garage Door Opener
Once the memory is cleared (or if you are programming for the first time), you can proceed with programming your garage door opener:
-
Prepare Your Garage Door Remote: Take your handheld garage door remote transmitter.
-
Position the Remote and Press Buttons: Hold the garage door remote approximately 1-3 inches away from the HomeLink buttons in your Infiniti. Simultaneously press and hold both the desired HomeLink button in your car and the transmit button on your handheld remote.
-
Observe the Indicator Light: Keep both buttons pressed until the red indicator light on your HomeLink system begins to blink. It will initially blink slowly and then transition to a rapid flash. This rapid flashing, which can last up to 90 seconds, indicates that the HomeLink system is learning the frequency signal from your garage door opener. Once the indicator light finishes flashing rapidly and may become solid or turn off, you can release both buttons.
-
Verify Programming: To confirm successful programming, press the newly programmed HomeLink button again. Your garage door should now activate. If the garage door opens, the programming is complete.
Programming Infiniti HomeLink: Hands pressing the HomeLink buttons located on the rearview mirror of an Infiniti vehicle to program a garage door opener.
Dealing with Rolling Code Garage Door Openers
Most garage door openers manufactured after 1996 are equipped with rolling code protection. This security feature changes the access code each time the remote is used, adding an extra layer of security. If your garage door opener uses rolling code technology, you will need to perform an additional “learning” step at the garage door opener motor unit.
Identifying Rolling Code Protection
After completing step 4 of the standard programming (pressing HomeLink and transmitter buttons simultaneously), observe the indicator light. If the light flashes for only about two seconds and then becomes a solid, continuous light instead of rapid flashing, your garage door opener likely utilizes rolling code protection.
Programming Rolling Code Systems
To program a HomeLink system with a rolling code garage door opener, follow these steps after completing the initial programming steps 1-4 above:
-
Locate the “Learn” or “Smart” Button: Access your garage door opener motor unit, usually located on the garage ceiling. Find the “Learn” or “Smart” button on the motor. The button’s location and appearance can vary depending on the manufacturer, so consult your garage door opener’s manual if needed.
-
Press the “Learn” Button: Press and release the “Learn” or “Smart” button on the garage door opener motor. Note: You typically have a limited time (usually around 30 seconds) after pressing this button to complete the next step. Having a second person can be helpful to expedite this process.
-
Return to Your Infiniti and Press HomeLink Button: Immediately return to your Infiniti and firmly press and hold the programmed HomeLink button for two seconds, and then release. Repeat this press-and-release sequence up to three times.
-
Confirmation: After these steps, the indicator light on your HomeLink system should become solid, indicating successful programming with the rolling code system. Press the programmed HomeLink button again to confirm that your garage door now opens and closes.
By following these detailed instructions, you should be able to easily program your Infiniti HomeLink system to operate your garage door opener. Enjoy the convenience of seamless garage access with your Infiniti vehicle. For further assistance or troubleshooting, consult your Infiniti owner’s manual or contact an authorized Infiniti service center.
