Program Genie Garage Door Opener to Car: A Comprehensive Guide

Integrating your Genie garage door opener with your car’s built-in remote system offers unparalleled convenience. No more fumbling for a separate remote – simply use the integrated buttons in your car to effortlessly open and close your garage door. This guide provides detailed, step-by-step instructions on how to Program Genie Garage Door Opener To Car systems like HomeLink and Car2U, ensuring a smooth and successful setup.

Understanding In-Car Garage Door Opener Systems: HomeLink and Car2U

Modern vehicles often come equipped with integrated garage door opener systems, most commonly HomeLink and Car2U. These systems feature buttons typically located on your car’s visor or overhead console, designed to communicate with your garage door opener. The advantage of these systems is their direct power source from your car’s electrical system, eliminating the need for batteries and providing a reliable, always-ready solution. Genie garage door openers are fully compatible with both HomeLink and Car2U.

Distinguishing between HomeLink and Car2U is straightforward. HomeLink systems usually have a single LED indicator, often accompanied by a house icon above the central button. Car2U systems, on the other hand, are characterized by three LED lights, one above each button. Recognizing your system type is the first step to successfully program genie garage door opener to car.

Programming Your Genie Garage Door Opener to HomeLink

HomeLink programming involves a simple three-step process: clearing any previous programming, training HomeLink with your Genie remote, and finally, programming HomeLink to your Genie opener. Follow these steps to program genie garage door opener to car with HomeLink:

Step 1: Clearing HomeLink System

Before you begin programming, it’s crucial to clear any existing programs from your HomeLink system. This ensures a clean slate for your Genie garage door opener.

1. Press and hold the first and third buttons on your HomeLink system simultaneously.
2. Continue holding until the indicator light blinks slowly at first, and then rapidly. This process usually takes about 20 seconds.
3. Release both buttons once the rapid blinking begins.

NOTE: Clearing HomeLink will erase all previously programmed devices.

Step 2: Training HomeLink with Your Genie Remote

This step involves teaching your HomeLink system to recognize the signal from your Genie garage door remote.

1. Choose a HomeLink button you wish to use for your Genie garage door.
2. Position your Genie remote approximately two inches away from the chosen HomeLink button.
3. Press and hold the button on your Genie remote.
4. Simultaneously, press and hold the selected HomeLink button.
5. Maintain pressure on both buttons until the HomeLink indicator light transitions from a slow blink to a rapid blink.
6. Release both buttons once the indicator blinks rapidly.

Step 3: Programming HomeLink to Your Genie Opener

The final step connects your programmed HomeLink button to your Genie garage door opener unit. The procedure varies slightly depending on whether you have a newer or older Genie model.

For Newer Genie Garage Door Openers (with Program Button):

Newer Genie openers are equipped with a “PROGRAM” button, typically located on the powerhead unit of the opener.

1. Locate the PROGRAM button on your Genie garage door opener powerhead.
2. Press and hold the PROGRAM button until the round blue LED illuminates.
3. Release the PROGRAM button. The long purple LED will start flashing.
4. Press and hold the chosen HomeLink button for two seconds, then release.
5. Repeat by pressing and holding the same HomeLink button again for two seconds and release.
6. Observe the long LED – it will flash blue and then turn off.
7. Press the HomeLink button a few more times to test and activate your garage door.

For Older Genie Garage Door Openers (with Learn Button):

Older Genie openers utilize a “learn code” button, often red in color, on the powerhead.

1. Locate the learn code button on your Genie garage door opener powerhead.
2. Press and release the learn code button. The red LED will begin to blink.
3. Press the desired HomeLink button once. The red LED will stop blinking and remain on.
4. Press the same HomeLink button again one more time. The red LED will turn off.
5. Press the HomeLink button again to operate your garage door.

NOTE: For further assistance, consult your vehicle’s owner’s manual, visit www.homelink.com, or www.GenieCompany.com.

Programming Your Genie Garage Door Opener to Car2U

Programming Car2U involves a similar process to HomeLink, starting with resetting the Car2U system, programming it to your Genie opener, and optionally, changing the default button settings. Here’s how to program genie garage door opener to car using Car2U:

Step 1: Resetting Car2U to Default Settings

Resetting Car2U ensures you start with the factory default configurations, which include pre-set assignments for different garage door opener brands.

• Default Car2U Button Assignments:
  • Button 1: Genie® Manufactured Openers
  • Button 2: LiftMaster® Manufactured Openers
  • Button 3: Wayne Dalton® Manufactured Openers

Car2U buttons in a car, designed for garage door and gate control

1. Press and hold buttons 1 and 3 on your Car2U system simultaneously for 20 seconds.
2. Continue holding until all three LEDs begin to flash.
3. Release both buttons. The Car2U system is now reset to factory defaults.

NOTE: Resetting Car2U will erase all previously programmed garage door openers.

Step 2: Programming Car2U to Your Genie Opener

Program Car2U to recognize and operate your Genie garage door opener, using either the Program or Learn button method depending on your Genie model.

For Newer Genie Models (with Program Button):

1. Press and hold the PROGRAM button on your Genie garage door opener powerhead until the round blue LED turns ON.
2. Release the PROGRAM button. The long purple LED will begin to flash.
3. Press and hold the designated Car2U button (you can use button 1, 2, or 3) for two seconds, then release.
4. Repeat by pressing and holding the same Car2U button again for two seconds and release.
5. The long LED will flash blue and then turn off.
6. Press the Car2U button a few more times to test operation.

For Older Genie Models (with Learn Button):

1. Press and release the learn code button on your Genie garage door opener powerhead. The red LED will start blinking.
2. Press the desired Car2U button one time. The red LED will stop blinking and stay illuminated.
3. Press the same Car2U button one more time. The red LED will turn off.
4. Press the Car2U button again to activate your garage door.

Step 3: Changing Factory Default Button for a Genie Opener

If you prefer to use a different Car2U button than the default (Button 1) for your Genie opener, follow these steps:

1. Press and hold buttons 1 & 3 for ONE SECOND and release. All three LEDs will light up solid red.
2. Press and hold the button (2 or 3) you wish to assign to your Genie opener. The corresponding LED will flash.
3. While continuing to hold the chosen button, press and release button 1.
4. Press and release button 1 again.
5. Release the button you held in step 2 and wait for the LED to stop flashing. This button is now programmed for your Genie opener.
6. Repeat Step 2 if you have a second Genie opener to program to another Car2U button.

NOTE: For additional support, refer to your vehicle’s manual, visit learcar2u.com, or www.GenieCompany.com.

By following these detailed instructions, you can successfully program genie garage door opener to car using either HomeLink or Car2U, enhancing your daily convenience and garage access experience.